NUFLO_Liquid_Turbine_Meters.jpg

Cameron Turbine Meters

Cameron NUFLO™ developed its first flowmeter for oilfield applications in 1957. The meter incorporated a tungsten-carbide shaft and bearing to withstand the rugged conditions of the oilfield environment. Over the years, this flowmeter has built an unsurpassed reputation for withstanding severe punishment while maintaining operational and measurement integrity.

|

More Info

Related Documents:


Technical Data Sheet

Turbine Meter FAQ's

Application Information Sheet

Specialty Turbine Flowmeters


Manuals:


Installation & Maintenance Manual

Repair Kits Manual

EZ-IN Manual

EZ-IN Manual - PED


Other Resources:


Serial Numbers Designation

Verifacation Math

Flowmeter Alloy CD4Mcu


Foreign Language Documents:


French Technical Data Sheet

Russian Documentation

 

Cameron NUFLO turbine flowmeters indicate flow rate and measure total throughput of a liquid line. As liquid flows through the meter and over the rotor, the rotor turns at a speed that is directly proportional to the flow rate. A magnetic pickup senses the rotor blades as they pass and generates an electrical (sine wave) signal. These electrical pulses are then transmitted to the flow measurement readout equipment.
End connections
Cameron offers turbine flowmeters in a variety of end connections and accuracy levels. Typical applications are:
  • Threaded
  • Grooved
  • Flanged
  • EZ-IN®
  • WECO® 1502
Flanged End Connection
Turbine flowmeters with flanged end connections are available in both raised-face (RF) models and ring-type joint (RTJ) models. Flanged materials can be carbon steel or stainless steel. All flanged NUFLO meters are equipped with slip-oflanges, which are then welded to the outside of the meter rather than being welded to the end of the meter body. Thus, the flange never comes into contact with the fluid being measured. The flanges are designed to mate with ANSI B16.5 flanges.
Grooved End Connection
Flowmeters with grooved end connections are available in 7/8-in. through 8-in. sizes.
EZ-IN® End Connection
Series BF turbine flowmeters with EZ-IN connections provide a cost-effective alternative to typical flanged-meter applications. Series BF meters with EZ-IN connections offer the accuracy, rugged construction, and maintenancefree operation of conventional NUFLO flowmeters plus the following advantages:
  • Lower installation cost.
  • Less expensive than a conventional, flanged meter.
  • Spreader nuts enable easy removal and inspection.
  • The raised-face EZ-IN meter will mate to any flange rated ANSI 150# to 1500#. The ring-joint (RTJ) version will mate to ANSI 900#, 1500# or 2500# RTJ flange. Specify flange type when ordering.
  • CE-marked 8 x 8-in. EZ-IN RF requires special centering rings.
WECO® 1502 Union End Connection
Flowmeters with 1502 end connections are commonly used in high-pressure oilwell service applications. Meter sizes 1”, 11/2” and 2” have 2” union end connections with a wing nut on one end and thread on the other end. The 3" meters have 3" union end connections with the option of a wing nut on one end and thread on the other, or threads on both ends. All 1502 union end meters have two pickup adapters. 

 

Share on FacebookShare on Twitter

 

NUFLO_1000_Series_TIM_Liquid_Turbine_Meter.png NUFLO 1000 Series TIM Liquid Turbine Meter

The unique replaceable rotor kit design of the NUFLO™ Series 1000 Top Insertion Meter makes this flowmeter one of the most user-friendly solutions on the market for liquid measurement. Replaceable rotor insert kits allow users to perform routine maintenance quickly and easily 1000 TIM is durable and well-suited to a wide range of applications, including measurement of contaminated liquids.


NUFLO_1502_WECO_Union_Liquid_Turbine_Flowmeter.jpg NUFLO 1502 WECO Union Liquid Turbine

The NUFLO™ 1502 WECO® Union Liquid Turbine Flowmeter incorporates a tungsten-carbide shaft and bearings to withstand the rugged conditions of the oilfield environment. Over the years, this flowmeter has earned an unsurpassed reputation for with-standing sever punishment while maintaining operational and measurement integrity. WECO union turbine flowmeters indicate flowrate and measure total throughput of a liquid line.

Call for pricing on:

  • High Pressure Threaded Industrial Grade
  • Modified For Nitrogen/CO2
  • Ball Berring Kits
  • Brazed For Corrosive Service
  • Modified For Cement Slurries

Magnetic pickup sold separately.


WMSeries.jpg NUFLO Cameron EZ-IN Turbine Meters

The Nuflo Cameron EZ-in style turbine meter is installed as a wafer between two user supplied flanges, offering economical alternatives and significant application advantages to conventional flange to flange, victaulic or threaded connections.  This line offers all stainless steel precision machined components with CD4MCu and/or 416 stainless steel rotors in line sizes from 3/8" through 8.0" and the same Nuflo Cameron Measurement reliability and accuracy.  Pressure ratings to 3700 PSI can be achieved with appropriate mating flanges.  Note that MWP is dependant on user supplied flanges. 

Installation kits and magnetic pick up sold separately.


WK_repair_kit.jpg NUFLO Cameron EZ-IN Turbine Meter Repair Kits

Nuflo Cameron Measurement OEM EZ-in repair kits are manufactured with the expected quality of this reknowned brand.  Repair Kits include  two each rotor supports, 1 each rotor and 2 each retaining rings or replacement screws as required.


NUFLO_Threaded_Turbine_Flow_Meter_without_mag_pickup.jpg NUFLO Cameron Liquid Turbine Meter

NUFLO™ turbine flowmeters indicate flow rate and measure total throughput of a liquid line. As liquid flows through the meter and over the rotor, the rotor turns at a speed that is directly proportional to the flow rate. The meter offers all stainless steel precision machined components with CD4MCu and/or 416 stainless steel rotors in line sizes from 3/8" through 10.0". End connection is NPT threaded standard, however other ends like victaulic, flanged, or sanitary are available on special request.

Magnetic pickup sold separately.


NUFLO_Cameron_Liquid_Turbine_Flow_Meter_Repair_Kits.jpg NUFLO Cameron 1502 WECO & Liquid Turbine Meter Repair Kits

Nuflo Cameron turbine repair kits purchased here are original OEM equipment. Manufactuered from stainless steel, the kits include 2 each rotor supports, 1 each rotor and 2 retaining rings. Note that the table below presents the information for the 1502 Weco style meter and standard threaded inline type meters.


nuflo_mag_pickup.jpg NUFLO Magnetic Pickup

Nuflo magnetic pick up flow meter sensors are active RF pickups driven by an external RF (carrier) signal conditioner. Together they complete an oscillating circuit. The output of this circuit is amplitude modulated when a ferrous, 316 stainless steel or aluminum object passes by the pickup coil. This change in modulation of the carrier frequency is converted into a square wave pulse by the signal conditioner for computing and/or further processing.


Categories

Back Home

More Info

Your Shopping Cart Bookmark and Share

Cameron Turbine Meters

 Oil & Gas Equipment Supply Center
Copyright © 2012 All Rights Reserved
Trademarks, trade names, and logos are the property of the registered agents displayed herein for informational purposes only.